AUTONET TV

Straight to the Point (Alignment Signs of Problems)

It’s just common sense that your vehicle will drive better if all the wheels are lined up with each other and the road the way the engineers intended.  When they’re not, that is called being out of alignment.   Here are some signs that your alignment has problems.

• Your steering wheel isn’t straight when your vehicle goes straight down a straight road. This one’s pretty easy to notice.  If your vehicle’s logo on the wheel is tilted, that’s probably not the way designers wanted it to be. Bring it in and have us check it out.
• Your steering wheel is vibrating on a smooth road or when you are accelerating.  While this could be caused by several different things, one possibility is misalignment.  If your steering wheel is shaking, it should be examined by a trained technician.
• Your vehicle is pulling to one side without you wanting it to.  Sometimes the configuration of the road will cause it to pull slightly left or right.  But if you find yourself constantly correcting course to keep your vehicle headed straight down the road, that’s worth having us look at your alignment.
• You’re going through tires like there’s no tomorrow. The tread on your tires should be wearing nice and evenly from the outside to the inside of the tire.  If the wear isn’t even, it could be your vehicle needs an alignment.

We have equipment designed to quickly and accurately measure your vehicle’s alignment.  We can make precise adjustments to make sure you are headed straight where you want to go.  Have your alignment checked regularly. It can help prevent more serious problems in the future and make your vehicle drive as beautifully as you remember it used to.

Auto Authority LLC
804 Witzel Ave
Oshkosh, Wisconsin 54902
920-231-1016
http://www.autoauthorityoshkosh.com

Road Trip? Check! (Trip Inspection)

After months of postponing travel far away from home, a lot of us can't wait to hit the road and scream "Road Trip!" again.  But how long has it been since the vehicle you're planning on taking has had a thorough inspection? And is it roadworthy for several days on the highway? Time to schedule a professional trip inspection in our service center. 

When it comes to long trips, before you go, make sure you can stop.  We can perform a break inspection.  Our technician will visually inspect your brakes for wear and how much life is left in the brake pads and rotors.  They'll also check your brake lines and fluids for fitness and fill.

If it's going to be a long trip, it's important that your engine stays lubricated.  The technician will see when the last time you had an oil change, check the levels and inspect the system for leaks.  If you are close to needing an oil change, it's best to have it done before the trip because no one wants to interrupt a vacation with an oil change in a strange place.  It's also better for your engine to have fresh, clean oil rather than driving with dirty, worn-out oil.

Comfort in any vehicle depends partly on the suspension system.  Our technician can examine shocks and struts so you can avoid an uncomfortable and potentially unsafe journey.  Oh, and you'll definitely want to make sure your wheels are aligned.  A long trip in an out-of-alignment vehicle can be a driving nightmare with potential steering problems and tire damage. 

A couple of little things some drivers take for granted are the engine air filter and wiper blades.  A dirty air filter can cost you money by reducing fuel economy; it adds up on a long trip.  And worn-out wiper blades can make visibility while driving in a rainstorm a blinding, unsafe adventure that you never want to experience, especially in unfamiliar territory.

If you're in the habit of having your vehicle regularly maintained, many of these items may be in excellent condition.  But considering the extra stresses a long road trip places on any vehicle, it's nice to have a set of our trained eyes give your vehicle a closer look. That way you'll be able to gaze YOUR eyes on sights like the Leaning Tower of Niles or the Gopher Hole Museum. 

Auto Authority LLC
804 Witzel Ave
Oshkosh, Wisconsin 54902
920-231-1016
http://www.autoauthorityoshkosh.com

Giving CV Joints the Boot! (CV Joint and Boot Replacement)

Ever wonder how your vehicle’s transmission is connected to your wheels? After all, when you hit a pothole or some other uneven part of a road’s surface, there has to be something that can maintain the connection between the transmission and the wheel yet keep everything moving at the same speed. 

That very cool device is called a CV joint, a kind of driveshaft running to each wheel.  The CV stands for constant velocity because it keeps the drive wheels moving at a constant speed (velocity).  They’re used mostly on front-wheel drive vehicles but also in rear-wheel and all-wheel drive vehicles.

The joints move up and down and adjust to bumpy surfaces.  Plus, they are covered in a rubber boot which protects them from road debris and also holds lubrication in.  There’s a CV joint and boot on the transmission side and one on the wheel side.  Unfortunately, the spot that usually fails first is that rubber protective cover (the boot).  After a lot of wear, tear, bumps, road hazards, heat, and you name it, the rubber rips and the lubrication leaks out.  At that point, it must be replaced. 

Here are signs to tell if your CV joint is bad.

• Your vehicle is pulling to one side as a wheel loses power or you feel a vibration while driving.
• You see grease on the inside or edge of your tires.  
• Your front tires won’t point in the same direction.
• You hear grinding or clicking when you turn.

Sometimes if a broken boot early is caught early, a technician can pack in new grease and replace just the boot.  But if the lubrication has leaked out and the joint is already wearing badly, the CV and boot both have to be replaced.  Give your vehicle the boot (as in a new boot) and CV joint, and you’ll be back on the road to your next destination.

Auto Authority LLC
804 Witzel Ave
Oshkosh, Wisconsin 54902
920-231-1016
http://www.autoauthorityoshkosh.com

Them's the Brakes (Brake Rotor Resurfacing)

Your vehicle's brakes wear out.  It's inevitable. You'll notice it when you step on the brake pedal and feel it harder to stop, or there's vibration when you are braking. 

Most modern vehicles have disc brakes that each use a brake pad that press on a disc (disc brakes!) called a rotor.  The friction between them enables you to stop, and each time you do a little bit of the pad and the rotor wears down.

The original brakes on vehicles used a rotor that was thick enough to last through at least two replacements of the pads.  But vehicle manufacturers who want to save costs and weight now make them thinner, and sometimes the rotors have to be replaced after the first pad replacement.  But not always.

Vehicle manufacturers specify a minimum thickness to provide safe braking.  Sometimes rather than having to have your rotors replaced, they can be put on a lathe and resurfaced.  In other words, the surfaces of the disc can be slightly shaved off so the surface is flat and doesn't wobble. 

Whenever you bring your vehicle in to have the brakes checked, the technician will measure the thickness of the rotors to see if they can be resurfaced without leaving them too thin for safe braking. If they can, with the right tools and skill, the rotors can be resurfaced.  If not, the rotors should be replaced. 

Discuss the options with your service advisor.  Our service center can recommend replacements that are designed to help stop your vehicle as well as or better than the vehicle's original rotors.

Either way, keep in mind that keeping your brakes in top condition can supply the margin of safety that may one day save your life or the lives of those around you.

Auto Authority LLC
804 Witzel Ave
Oshkosh, Wisconsin 54902
920-231-1016
http://www.autoauthorityoshkosh.com

Oil's Well That Ends Well (Oil Change Grades and Weight)

Changing your oil regularly is one of the most important things you can do to keep your vehicle running well.  And knowing the right type of oil to use is also very important. 

Engine oil is classified by weight, but it doesn't refer to how much the oil would weigh if you put it on a scale.  It refers to viscosity, or how easily the oil flows through the engine.  Most engines operate normally at around 210°F/99°C.  The viscosity, or weight, is assigned a number by how well it flows at that temperature.  The lower the number, the more freely it flows. 

Most vehicle engines use what's called a multigrade oil which behaves differently in different temperatures. Multigrade oils have a "W" in their viscosity number that you may have seen on a bottle of oil, something like 5W30.  The W stands for winter and shows how freely it flows in colder temperatures.

That means a 5W30 oil will behave like a 5 weight oil in lower temperatures (less viscous or thinner) and a 30 weight oil in warmer temperatures (more viscous or thicker).  That's important on a cold day because the oil needs to behave like a thinner oil when you start your engine since it need to lubricate engine components immediately to protect the metal components. Then as the engine warms up, it behaves like a thicker oil to prevent friction among those parts.  Pretty neat trick, right?

The type of oil you use can differ depending on what type of climate you operate your vehicle in and how your vehicle is used (carrying big loads, towing, etc.). Your owner's manual contains several different recommendations based on these factors.  Your service advisor can recommend the right oil for your needs.  Like Shakespeare said, "Oil's well that ends well."

Auto Authority LLC
804 Witzel Ave
Oshkosh, Wisconsin 54902
920-231-1016
http://www.autoauthorityoshkosh.com