AUTONET TV

Clean Machine (Fuel and Air Induction Cleaning)

As your vehicle ages, its performance isn’t quite what it used to be, but many of us never notice the change because it’s gradual.  So here are a few questions to ask yourself.  Does your vehicle feel like it doesn’t have the pep that it used to? Have you noticed your fuel economy isn’t quite as good as it once was? Does it idle roughly or is it hard to start?  Do you hear the engine knocking? Has it recently failed an emissions test?

All of those can be signs that your fuel and air induction systems are dirty and need cleaning.  Your fuel system takes gasoline from the tank to the engine’s combustion chambers where fuel injectors spray fuel that mixes with air and is ignited by spark plugs.  Black carbon deposits eventually can build up, obstructing fuel flow and diminishing your engine’s performance and fuel efficiency.

The air induction system is what allows air to go into the engine’s combustion chamber.  Getting the proper air flow is necessary for you to quickly start your vehicle, accelerate, and perform the way it should and idle smoothly when you’re standing still.  Like the fuel system, your air induction system can get blocked up with deposits and other contaminants.

A professional fuel and air induction cleaning can help restore your performance and fuel economy, especially when you are experiencing problems.  A technician will use specialized chemicals that can remove the carbon buildup.  In extreme cases, they will remove the fuel injectors and clean them with specialized tools.  

After cleaning, you may notice how much more pep your vehicle has and how smoothly it runs.  Keep your fuel and air induction systems clean and enjoy your vehicle’s performance improvements.

Auto Authority LLC
804 Witzel Ave
Oshkosh, Wisconsin 54902
920-231-1016
http://www.autoauthorityoshkosh.com

Out of Joint (CV Joint and Boot Replacement)

If you have a front-wheel-drive vehicle, it has components called CV joints which enable you to turn your wheels smoothly. The CV stands for “constant velocity.” In essence, it’s a set of gears that connect a shaft that allows power from the transmission to be sent to the wheels.  When you turn the wheels, no matter what angle, the input velocity rotation will be equal to the output. Thus, the name, CV (constant velocity) joint. Other vehicles with 4-wheel drive and all-wheel drive also use CV joints.  

If one of your CV joints isn’t working right, you may find your vehicle difficult to handle.  If one breaks, your vehicle may stop moving.  So, it’s important that CV joints be in top working condition.  The joints need a lot of lubrication, so they are surrounded by grease.  There’s a rubber enclosure around them called the boot which holds the grease in and protects CV joints from the elements. 
 
The biggest problems come when one of those rubber boots cracks.  Water and dirt can then get into the joint, causing it to wear down and lose all its vital lubrication.  It’s important to have your CV joints inspected regularly so a technician can spot cracks before the CV joints are ruined.  Sometimes just the boot can be replaced before any major damage is done.  But when the joint does go bad, it must be replaced.  

Signs your CV joint needs changing out? You might hear a clicking sound when you turn if the CV joint is worn out. You might notice some thick, black grease around your wheel or on the pavement where you park your vehicle.  You might also feel your vehicle vibrate when you’re going fast.

If you suspect you might have a bad CV joint, bring your vehicle in so a technician can determine what’s going on.  Keep your CV joints in good shape and reduce the risk of them seizing up at an inopportune time so you can avoid being stranded.

Auto Authority LLC
804 Witzel Ave
Oshkosh, Wisconsin 54902
920-231-1016
http://www.autoauthorityoshkosh.com

How Cool is That! (Coolant level sensor replacement)

Your vehicle’s engine runs hot.  It should, since it’s a series of little explosions that create the power that gets you going where you want to go.  To keep the engine cool, engineers have designed wonderful cooling systems that use liquid coolant, hoses, and a radiator to transfer the heat from the engine to the outside air. 

In order for the system to work right, it has to have the right amount of that liquid coolant in it.  So that you know when the coolant has dipped below the correct amount, there is a sensor that keeps an eye on it.  When the coolant gets low, that sensor lights up a signal on the dash to alert you.  It may literally say “Check Coolant” or it may have a picture that looks like an old-style bulb thermometer sitting in liquid.  Your owner’s manual will usually tell you exactly what the one in your vehicle looks like.

If that sensor system isn’t working right, you could wind up driving for a long time with not enough coolant in the engine, and the excess heat can cause some extensive—and expensive—damage. 

There are a couple of ways you will know if something’s wrong with your coolant level sensor.  One is when you top off the coolant tank, and the low coolant light stays on.  If you suspect yours might be having a problem, bring it in so we can thoroughly check your coolant system.

If it is a sensor, we can run a test to see where the problem is in your cooling system.  It could be a bad sensor, but it also could be that there is something causing your coolant level to be low.  If the sensor needs replacing, the technician will replace it, fill your coolant level to the manufacturer’s recommended level, and test for any leaks in the system.  Really, how cool is that?

Auto Authority LLC
804 Witzel Ave
Oshkosh, Wisconsin 54902
920-231-1016
http://www.autoauthorityoshkosh.com

test

Full Stop (Brake Master Cylinder Replacement)

When you step on your brake pedal, you want to feel confident that your vehicle’s going to stop.  If your brakes aren’t working right, it’s a risk to your safety and the safety of others on the road.  After all, you’re driving a machine that weighs thousands of pounds, and you have to be able to stop that big machine quickly and with control, especially with some of the speeds you travel on the highways. 

The heart of your vehicle’s brake system is the master cylinder.  When you apply the brakes, the master cylinder has pistons, springs, and brake fluid.  That fluid amplifies and distributes the force of your foot through brake lines to calipers at all your wheels.  Those calipers squeeze down on rotors or discs, which is what slows down and stops your vehicle.

For safety, a master cylinder has two cylinders, one for two wheels, and the other for the remaining two wheels.  That way, if there is a failure in one, you’ll still have braking power at half your wheels.

The master cylinder doesn’t last forever, of course, and here are some signs it may have problems.  When you press on the brake pedal, it feels soft and spongy.  You may see the brake light on your instrument panel go on.  You may notice brake fluid leaking, or it may be discolored. 

All of those are signs of brakes that need attention, and among the possible culprits is a master cylinder that has failed.  When you bring it in for a technician to look at, they’ll check not only the master cylinder but also the rest of the components, such as pads, discs, shoes, brake lines, and hoses.  If your master cylinder needs replacing, we’ll make sure all the other parts meet the manufacturer’s specs as well. 

Brakes are important.  Really important. Full stop.

Auto Authority LLC
804 Witzel Ave
Oshkosh, Wisconsin 54902
920-231-1016
http://www.autoauthorityoshkosh.com